21st Century Maida Regulator
21st Century Maida Regulator 21st Century Maida Regulator
Chevron down Icon
$89
Current inventory: In stock.

The voltage regulator design below deals with high voltages — LETHAL voltages. If you are not comfortable or qualified to deal with these potentially deadly voltages, please do not attempt to build this circuit. Proceed at your own risk, expense, and responsibility. 

Since its release in 2012, the 21st Century Maida Regulator has become widely adopted by DIY tube amplifier enthusiasts appreciating its ultra-low noise floor and extremely high ripple regulation. In this second revision of the circuit, I take its performance to a whole new level.

Regulator Impact on Sound Quality

When used in tube amplifiers, single-ended and push-pull designs alike, the 21st Century Maida Regulator results in remarked improvements in sound quality. Most commonly, builders report:

  • Much bigger sound stage.
  • Firmer and punchier bass.
  • Huge, open, and natural midrange.
  • Clearer and more precise treble.
  • Zero hum.

These properties are the direct result of the low output impedance, low noise, and phenomenal ripple rejection offered by the 21st Century Maida Regulator. The 21st Century Maida Regulator is also being employed in commercial builds with stellar results. For example, you can read Don Sachs' impressions of the regulator here: Don Sachs Consulting - Custom KT88 Amplifier.

The input to the 21st Century Maida Regulator should be a rectified DC voltage. The input voltage should be at least 15 V higher than the output voltage at all times, including at the bottom of the ripple valleys.

The 21st Century Maida Regulator is compatible with both tube and silicon rectifiers and requires only a small reservoir/smoothing capacitor in the power supply. The extraordinary ripple rejection is shown in the oscilloscope screen shot below. 

21st Century Maida Regulator input and output voltage

In the above measurement, the input voltage was a full-wave rectified sine wave with a 50 µF reservoir capacitor. The load current was 200 mA. The resulting ripple voltage on the reservoir capacitor is clearly evident above and measures about 25 Vpp. The output voltage is completely free of ripple or hum - even at the highest resolution of the oscilloscope (20 mV/div). The measurement bandwidth for above measurement was 20 MHz. 

The 21st Century Maida Regulator offers the following features:

  • True floating regulator design.
  • Ultra-low output impedance across the audio band.
  • Phenomenal ripple rejection.
  • Output voltage and current set by two user-selected resistors.
  • ±10 % adjustment range on output voltage.
  • Soft start.
  • Capable of start-up into a purely capacitive load (up to 47 µF verified).
  • Start-up into harsh load (2.2 A inrush light bulb load).
  • Handles high di/dt current pulses such as the ones caused by loose connections in tube sockets.
  • No need for expensive and bulky high-power resistors.
  • Optimized thermal performance.
  • Ultra-low supply inductance due to the elaborate use of planes and pours.
  • Small 2.25×2.6 inch (57×66 mm) board footprint.
  • Gold plated PCB. Designed, manufactured, and assembled in Canada.

The specifications for the 21st Century Maida Regulator are tabulated below.

Parameter Value Notes
Max. Input Voltage 750 V
Max. Output Voltage 525 V
Max. Output Current 800 mA Vin * Iout(sc) < 230 W
Output Impedance < 0.06 Ω 1 kHz, Vout = 400 V
Residual Noise and Hum 20 µV RMS Vout = 400 V, BW = 1 MHz
Output Voltage Adjustment Range ±10 %
Drop-Out Voltage 15 V
Regulator Supply Current 2.0 mA
Minimum Load Current 0 mA